Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

(ASCEND) 2.0.7 for Max TNT

Release 2.0.7 for the MAX TNT has been given to support.

 Corrections in 2.0.7:
 TR 2449:    Refresh -t did not update initial-banner from RADIUS.
 TR 2525:    MAX TNT showed zero packet counts for MP+ calls.
 TR 2571:    Ascend MIB did not report second slot of modem cards as
Occupied.
 TR 2860:    FE-18 on E1 card with R2 signaling.
 TR 3016:    TCP headers were corrupted when VJ compression was enabled.
 TR 3088:    Filters did not work for RADIUS-authenticated
terminal-server logins.
 TR 3092:    Wandialout SNMP MIB table did not contain
callReferenceNumber.
 TR 3103:    Data filter caused modem card to reset.
 TR 250207:  Only timeouts initiated connection attempts to a Secondary
Home Agent.
 TR 250279:  IP routing table was sometimes not updated correctly.
 *  Terminal-Server profile now validated when written.
 *  Changes to RADIUS retry behavior.
 *  T-Online: ZGR request changes.
 *  RADIUS Auth-Boot-Host validation.
 *  Data filter did not work from Answer profile as default for RADIUS.
 *  System crashed with error during Status window display on console
port.
 *  Local directed broadcast packets (including RIP packets) were
dropped.
 *  DSL related changes.
 *  T-Online: IM 30733/AT 255409
 *  ATMP performance enhancement.
 *  Syslog messages reported incorrect disconnect codes for TCP-Clear
calls.
 *  The 100BT Ethernet port was not reported in SNMP.
 *  SNMP Frame Relay circuit table (RFC 1315) did not display all DLCIs.
 *  System could reset when loaded with 16 xDSL slot cards.
 *  Modems sometimes failed to handshake under heavy load.
 *  Changes to callCleared event in the SNMP eventTable.
 *  Data could become corrupted when multiple Telnet sessions were
active.
 *  Frame Relay link with LMI enabled failed to come back up after heavy
load burst.
 *  Periodic cleanup of allocated resources is now performed.
 *  Disconnect Cause 101 with subsequent login failures.
 *  HDLC card FE2 prevention.
 *  HDLC card could reset without fatal error under heavy load.
 *  Data filters did not take effect when applied in a slot-card
IP-Interface profile.
 *  Home Agent sometimes did not send Foreign Agent an error condition
result code.
 *  HDLC card Warning 106.
 *  RADIUS Attribute 7 was not interpreted if Attribute 6 was not
defined.
 *  Memory leak could occur following terminal-server login.
 *  RADIUS ID authentication retry caused timeouts related to the T310
timer.
 *  IP-Pools command output sometimes contained garbage characters.
 *  The MAX TNT was not processing next-hop routes in RIP-v2 input
packets.
 *  Modem card could fail without fatal-log with pool calls.
 *  Userstat command could eventually cause Warning 111 (buffer too
big).

 Enhancements in 2.0.7:
 *  Configurable status and command window sizes
 *  ATMP resiliency in Primary and Secondary Home Agents
 *  Switched mode for xDSL lines
 *  Configurable transmit and receive data rate limits for SDSL
 *  X.75 support
 *  Profile pathname and status indicators
 *  Messages about writing profile changes

 Release 2.0.7 contains the following Rockwell modem code versions:
 *  V.34: V1.610G19-V34_DP
 *  56K: V1.160_TEST-K56_DLP_CSM

Matt Holdrege		http://www.ascend.com	matt@ascend.com
++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>