TCLUG Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

isapnp




   Ran isapnp. The following is the part of the generated file isapnp.conf for
what should be the sound card.
   Which lines should I uncomment?
 
# $Id: pnpdump.c,v 1.9 1997/06/10 21:37:32 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Board 1 has serial identifier 04 ff ff ff ff 37 09 63 0e
# Board 2 has serial identifier 7e 00 00 01 00 19 41 6d 22

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier 04 ff ff ff ff 37 09 63 0e)
# CSC0937 Serial No -1 [checksum 04]
# Version 1.0, Vendor version 0.1
# ANSI string -->CS4237B
#
# Logical device id CSC0000
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CSC0937/-1 (LD 0
#     ANSI string -->WSS/SB

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 0 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 1 (CHANNEL 0))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0534
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 1 (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))

#       Start dependent functions: priority acceptable
#       First DMA channel 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 1 (CHANNEL 0))
#       IRQ 5, 7, 9, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 1 (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0260
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))

#       Start dependent functions: priority functional
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 0 (CHANNEL 0))
#       IRQ 5, 7, 9, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 1 (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0300
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))

#     End dependent functions
# (ACT Y