Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: (ASCEND) MaxTNT 1.3Ap6 ip/32 netmask bug


Kevin,
Hi.
Here's what I have when i have entered the configuration and then I typed
write.

____________________________
station* = angepin-fvs
active = yes
encapsulation-protocol = mpp
called-number-type = national
dial-number = 96517778
clid = ""
ip-options = { yes yes 208.10.139.253/32 0.0.0.0/0 1 60 120 no no 0 
                                                   0.0.0.0 routing-off+
bridging-options = { 0 no }
session-options = { "" "" no 120 no-idle 120 "" 0 }
telco-options = { ans-and-orig no off 1 no no 56k-restricted 0 "" "" no
yes }
ppp-options = { chap-ppp-auth their passwords stac 1524 no 600 600
}
mp-options = { 1 1 2 }
mpp-options = { "" quadratic transmit 1 1 15 5 10 70 }
fr-options = { "" 16 "" no "" 16 }
tcp-clear-options = { "" 0 no "" 256 20 }
v120-options = { 7 3 1500 30000 256 }
answer-options = { }
usrRad-options = { global 0.0.0.0 1646 "" 1 acct-base-10 }
calledNumber = ""
tunnel-options = { disabled 0 "" "" 5150 "" "" }

admin> list ip
ip-routing-enabled = yes
vj-header-prediction = yes
assign-address = no
fill-1 = 0
remote-address = 208.10.139.253/32
netmask-remote = 255.255.255.255
if-remote-address = 0.0.0.0
local-address = 0.0.0.0/0
netmask-local = 0.0.0.0
routing-metric = 1
down-metric = 7
preference = 60
down-preference = 120
private-route = no
multicast-allowed = no
address-pool = 0
auth-pool-address = 0.0.0.0
ip-direct = 0.0.0.0
rip = routing-off
route-filter = ""
ospf-options = { no 0.0.0.0 normal 30 120 5 simple ascend0 10 1000 type-1c0:00+
multicast-rate-limit = 100
client-dns-primary-addr = 0.0.0.0
client-dns-secondary-addr = 0.0.0.0
client-dns-addr-assign = yes
client-default-gateway = 0.0.0.0/0
_________________________________



When I EXIT out and telnet back in to the TNT and view the
configuration, the netmasks says the following
and the routing is all screwed up and no one can get anywhere.  I am
telnetted in but the connection is going up and down.

remote-address = 208.10.139.253/0
netmask-remote = 0.0.0.0

I have retyped and resaved the netmask many times and it always changes
back to zeroes.

Karen



On Thu, 13 Nov 1997, Kevin Smith wrote:

> At 10:47 AM 11/13/97 -0600, WCN Customer Service wrote:
> >
> >I have ISDN customers dialing into a MaxTNT with Software version 1.3Ap6.
> >The TNT has 2 cards 56k modems and a 10/100 Mbps ethernet module, and T1
> >module.  I want to give an ISDN caller a static ip.  I set remote-address
> >to their ip/32 and netmask-remote to 255.255.255.255 and it ALWAYS changes
> >the netmask back to /0 and 0.0.0.0  However, the TNT will retain a
> >netmask like /27 or /29 ...but not /32.  Can someone help?
> 
> Where is the netmask being changed - in the routing table, or on the client
> end ? Do you have an extract of the config and the routing table we
> can review to look into this further (it is a very common setting, so I'm
> stumped for now).
> 
> 
> Kevin
> 
> 
> ++ Ascend Users Mailing List ++
> To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> 

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>
Follow-Ups: References: