RE: (ASCEND) Configuring Max 4048 for NON-PRI T1

["Steven Copeland" <scopeland@pldi.net>]

Tim, here is how I have my 4048's configured for CT1.  Also, deep in the
Ascend documentation, there is a statement that when using Channelized
T-1's, the Telco cannot send any digits or the call will fail.  If the Telco
is sending digits, then please ask them to turn that feature off.

Probably what you are seeing is that you make a call into the MAX, see a
channel answer then immediately get a busy signal.  This is most likely  a
case of the Telco sending digits to the max.

Sig Mode=Inband
NFAS ID num=N/A
Rob Ctl=Inc-W-200
Switch Type=N/A
Framing Mode=D4
Encoding=AMI

Ch 1=Switched
Ch 1 #=
Ch 1 Slot=3
Ch 1 Prt/Grp=0
Ch 1 TrnkGrp=N/A
and so on


^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Thank You,
Steven Copeland

Senior Network Administrator/Internet Coordinator
Pioneer Internet - A service of Pioneer Long Distance, Inc.
Subsidiary of Pioneer Telephone Cooperative, Inc.
scopeland@pldi.net
405-375-0880
http://www.pldi.net
http://www.pld.net
http:/www.ptci.com

> -----Original Message-----
> From: owner-ascend-users@max.bungi.com
> [mailto:owner-ascend-users@max.bungi.com]On Behalf Of Tim Connolly
> Sent: Tuesday, November 30, 1999 3:59 PM
> To: 'ascend-users@bungi.com'
> Subject: (ASCEND) Configuring Max 4048 for NON-PRI T1
>
>
>     I'm still having trouble finding the lingo for these circuits. the
> telco calls them digital trunks, although in my book they aren't
> digital... Ascend's manual calls them Inband signaled T1's. And I call
> them channelized T1's. Basically I ordered incoming dialup
> lines without
> the option of having ISDN signalling. Now comes the fun part....
>     First off, I've never used D4/AMI before... Secondly, I've
> configured nothing but T1 PRI's, no "inband" T1's...
>     Following the book's suggestion I used:
> >Ch 1=Switched
> x  Ch 1 #=05
>  x  Ch 1 Slot=3
>  x  Ch 1 Prt/Grp=0
>  x  Ch 1 TrnkGrp=N/A
>  x  Ch 2=Switched
>  x  Ch 2 #=05
>  x  Ch 2 Slot=3
>  x  Ch 2 Prt/Grp=0
>  x  Ch 2 TrnkGrp=N/A
>
> But no matter what I try, I always get a busy signal when my
> Max shows a
> ring detect. any ideas ?
>
> -- Tim Connolly tec@mountain.net     MountainNet, Inc.
> -- Network Administrator             2816 Cranberry Square
> -- (304) 594-9075/fax-9088           Morgantown, WV 26508
>
>
> ++ Ascend Users Mailing List ++
> To unsubscribe:	send unsubscribe to
> ascend-users-request@bungi.com
> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
>

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>