(ASCEND) 7.2.3 for the Max

[Matt Holdrege <matt@ascend.com>]

TAOS 7.2.3 software for the MAX family has been given to Customer Support.
This release contains the following:

Corrections
TR 2879: In Terminal Server menu mode, unavailable selections could be chosen.
TR 2987: MAX 4000 was running without V.110 card, but it answered a V.110 
call.
TR 3828: You could not disable modems via SNMP if the MAX was answering too 
many incoming calls.
TR 4210: ATMP RIP was sent by home agent, even though ATMP RIP was set to Off.
TR 4251: Routing problems occurred because dynamic routes were not updated 
to the Max that had the outgoing profile.
TR 4323: PIAF could not communicate with CLID auth using RADIUS.
TR 4615: Max 4004 reset occasionally with FE1. This occurred with ISDN 
calls, 4 PRI lines and using IP protocol.
TR 4679: MAX reset occasionally with FE8 when PPTP was used from PIAFS 
terminal.
TR 4868: MAX supporting OSPF, generated warnings 175, 200, and 201.
TR 4879: Protection violation errors related to IPX were occurring.
TR 4888: Max units with L2TP configurations would have some configuration 
corruption when upgrading to 7.0+ software.
TR 4922: EchoSuppressToneDisable parameter disabled tone for all calls.
TR 4967: Variables were missing for L2TP/ATMP/PPTP bits in sysSPROM option 
in Ascend MIB.
TR 4996: LNS could not do CLID/DNIS authentication.
TR 5181: Radius Accounting was not working when Auth-Type was set to 
RADIUS/LOGOUT.
TR 5305: The response to the ID packet was being rejected due to an older 
code version.
TR 5314: Low ISDN login rate in stacking environment.
TR 5325: The IP Global profile was not available during system initialization.
TR 250283: Using different trunk numbers for each BRI channel did not work.
TR 258640: The MAX 4000 was not setting the M-BIT during data transfer 
between the modem client and the X25 Host.
TR 258646: L2TP and AAC authentication failed when a single RADIUS server 
was used.
TR 258648: Overlap receiving ISDN mode option was missing in the febk.m40 
software load.
TR 258738: MAX did not differentiate between user-defined and telco-defined 
CLID numbers.
TR 258756: FTP failed when using Firewall and NAT on the same Dialout profile.
TR 258787: The Filter ID attribute was not working.
TR 258813: Occasionally, the MAX showed available modems as busy with the 
avm diagnostic command.
TR 258821: Ghost ATMP tunnels were created and were not removed on the Home 
Agent.
TR 258831: LNS could not do CLID/DNIS authentication.
TR 258836: The Max units reset with a FE29 after having received multiple 
Warning 104 messages.
TR 258851: The MAX unit reported incorrect baud rates for L2TP and PPTP 
sessions.
TR 258864: SNMP trap was not being sent when E1/PRI went from DF status to 
TE status.
TR 1000145: MAX 6000 reboot with FE17 and warning 179. This occurred under 
heavy data over ISDN, R2 outdial load.
TR 1000195: FE 29 occurred during MP outdial.
TR 1000214: MAX path MTU discovery was broken for ATMP GRE. MTU was zero 
and force fragmentation was off.
TR 1000221: After reboot, the MAX 6000 would not accept or send calls.
TR 1000223: Incorrect information element was being sent in the call 
proceeding the PRI call.

Conexant (formerly Rockwell) firmware versions
Digital modem module Conexant versions
K56-8, -12, and -16 2.098
V.34 Modem-12 1.610G24
V.34 Modem-8 1.610G19

Notice of discontinuance:
Software support for v.34 slot cards.


++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>