Real Time Ascend Maling List Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ASCEND) Framed-Address
You'll have to set the netmask using Framed-Netmask = 255.255.255.255
as one of the reply items in your RADIUS file. Also remove the
Ascend-Assign-IP-Pool = 0 -- it's unnecessary for a static IP assignment.
John
At 04:49 PM 9/22/99 -0600, Brian Sullivan wrote:
>HI ALL,
>
>> Try to enable RIP or OSPF both at MAX and your backbone router...
>> When a static IP user connetcs to MAX, Max should advertise this user's
>> IP routing to your backbone router. (I assume that user's framed IP is not
>> in the
>> Max's ethernet IP subnet range. If so there shouldn't be a problem if you
>> set
>> Ethernet>Mod Config>Ether Options>Proxy Mode=Active...)
>> Yasin KAPLAN - INTRAkets
>> Teknik Mudur - Technical Manager
>> Tel:+90 (216) 3276930 Ext. 116 Fax: +90 (216) 3276924
>> http://www.intrakets.com.tr/ kaplan@intrakets.com.tr
>
>This is the odd thing, the Static IP address that I'm assigning IS in the
>same IP subnet range as the Max's ethernet... I do have Proxy
>Mode=Active... The pool of dynamic IP addresses is also in the same subnet
>range as the Max's ethernet... Here's a copy of my Radius record for a
>static user:
>
>username Password="password"
> User-Service = Framed-User,
> Framed-Protocol = PPP,
> Framed-Address = 192.168.0.23,
> Ascend-Assign-IP-Pool = 0,
> Ascend-Idle-Limit = 900,
> Ascend-Data-Filter = "ip in forward tcp est",
> Ascend-Data-Filter = "ip in forward dstip 192.168.0.0/23",
> Ascend-Data-Filter = "ip in drop tcp dstport = 25",
> Ascend-Data-Filter = "ip in forward"
>
>Is the "Ascend-Assign-IP-Pool=0," causing troubles? Do I need a
>"Framed-Netmask" attribute?
>
>Thank all of you for your help...
>
>Brian Sullivan
>brian@polnow.net
>
>
>>
>> -----Original Message-----
>> From: owner-ascend-users@max.bungi.com
>> [mailto:owner-ascend-users@max.bungi.com]On Behalf Of Brian Sullivan
>> Sent: Tuesday, September 21, 1999 12:40 AM
>> To: ascend-users@bungi.com
>> Subject: (ASCEND) Framed-Address
>>
>>
>> I'm trying to give certain dial-in users static IP address assignments.
>In
>> this case the static IP address assignment is outside of the pool of
>> addresses I have assigned to the Ascend 4048. The user is authenticated
>> with no trouble, the IP address is properly assigned, but the user cannot
>> get any data across the PPP connection. If I attempt to ping that
>assigned
>> IP address I get no data bounced back...
>>
>> Is there a setting that I need to change to tell the Ascend 4048 to route
>IP
>> traffic when a static IP address is assigned?
>>
>> Thanks in advance for any help...
>>
>> Brian Sullivan
>> brian@polnow.net
>>
>> ++ Ascend Users Mailing List ++
>> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
>> To get FAQ'd: <http://www.nealis.net/ascend/faq>
>
>++ Ascend Users Mailing List ++
>To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
>To get FAQ'd: <http://www.nealis.net/ascend/faq>
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>